how are you getting around the electrical permitting? Asking for a friend.
Announcement
Collapse
No announcement yet.
200 Square Foot Tiny Workshop
Collapse
X
-
Originally posted by Rubberdown View Posthow are you getting around the electrical permitting? Asking for a friend.
Comment
-
The power is on, and I spent this weekend getting the workshop insulated! Here in south Texas, we are not getting any autumn weather yet, so it was hot, sweaty, itchy work, especially wearing long sleeves and a mask.
I started with the ceiling, so that was a full day working over my head. I am pleased with the results.
There was a lot more to do to finish out the walls, though that work went a lot smoother.
I cut it WAY too close on the amount of material I bought, but I was able to use every scrap to finish out the walls. I do plan to go back with some expanding foam to fill in the corners, and that should cover everything.
It's amazing how much this made a difference in sound! It's so much quieter in here, and that's going to be great for filming my videos. Speaking of which, this episode is live, and I will link to it below.
Comment
-
I am pleased to share the next stage in this tiny workshop build. I spent some time installing 3/8" plywood as the wall covering inside the shop, and it turned out great! I still have to trim things out, but it's awesome having a (near) finished look inside.
I originally planned to use 5mm poplar plywood from Lowes, as it was one of the less expensive options, and looked nice. However, about the time I was set to go buy it, it jumped considerably in price - almost a 50% increase! I then opted for the 3/8" which was a few bucks cheaper, and I figured having the extra thickness would work out better in the long run. I needed 27 sheets to complete the shop, which worked out to about 900+ pounds of lumber.
Once I got some final trim pieces in place, and cleared out the shop, I began installing the ceiling panels. I screwed a couple scrap boards together to screw to the top plate of the wall hold the bottom of the plywood, and pre-drilled all my screw holes to help the solo installation go smoother. Other than some on-the-fly readjustments, it went ok - just slow and steady.
I bought the WEN Track Saw a while back, paired with 2 Powertec Tracks, and I used the heck out of it for this stage of the build. It was nice to simply line up my marks and go, and be confident of a straight, accurate cut. I used the stock blade for this, and it worked just fine, though I will definitely be buying a better blade for future projects.
Putting up the wall panels was easier, though still slow-going, since I wanted to ensure all my measurements were dead-on, especially for the outlets and fixtures. There are a few places that I'll notice where things aren't perfect, but I'm pleased for the most part. I did screw up one panel around the door, where I measured an inset and cut from the wrong side, but it was nothing a scrap piece of ply couldn't fill in. I didn't total it up, but I used almost an entire 1,000 piece box of 1.5" screws here.
I probably took more time than necessary on this stage, just being careful in my measuring and cutting. I spent 4 days getting this done, so putting up that last panel felt really, really good. Once I get the trim around the doors, windows, and edges, the interior will basically be done and ready to actually do some shop work!
I put a lot of detail of my progress into the video, so you can see how it all came together. I'll post that below.
Comment
-
And just like that, 7 months later, the build is done! I finished up the interior trim, and painted the outside. I am very pleased with the results, and I can't wait to get in there and start working on projects!
I had the paint matched to our house paint. It's hard to see here, but the match is outstanding, especially with the stucco pattern Hardie on the shop and the real stucco on the house.
I'm loving the plywood interior, and the trim brings everything together well.
I've been moving my tools back into the space, and I'm going to purge some of the stuff before I move it in. Ideally, this needs to stay as clean and organized as I can make it to be usable.
The end of the build is only the beginning, so from here on out, I'll be posted my projects and builds in this thread. Thanks for following along!!!
Comment
-
Originally posted by TreyRo View PostDo you like the lights you ended up with on the interior? I've got a tac room in our new barn that i'm using as my workshop that needs a little more light.
Comment
Comment