Announcement

Collapse
No announcement yet.

69 C10 Build

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #76
    Originally posted by muzzlebrake View Post
    Curious minds would like to know numbers
    300 cfm @ .550 lift would be ideal on intakes with 200+ on exhaust
    I’ll take a pic of the sheet sir

    Comment


      #77
      Originally posted by Blane View Post
      What did you use on the frame? Just a gloss Krylon or some other can spray or did you use a gun?
      Pressure washer, degreased and Krylon sir

      Comment


        #78
        Originally posted by muzzlebrake View Post
        From your head pictures it looks to me like they removed any shrouding from around the valve seats and the valve guide bosses in the port runners have been cleaned up and reduced obstruction. Nice CNC work in the combustion chambers. I like the satin finish in the ports. Helps keep fuel atomized for better mix and burn.

        Now for some good exhaust to pull all that power out
        It will definitely have a bad *** exhaust

        Comment


          #79
          Looking good man. What exhaust are you going to run?

          Comment


            #80
            Originally posted by COOLDAD1 View Post
            Looking good man. What exhaust are you going to run?
            Debating and open to suggestions. When I get the old motor out I’ll holler at you sir

            Comment


              #81
              Glad to see that grill changed. Man it looks good.

              Comment


                #82
                Originally posted by denimdeerslayer View Post
                Glad to see that grill changed. Man it looks good.
                I agree. It made a huge difference and was one of the first things I wanted to change

                Comment


                  #83
                  That setup screams Borla Atak with an X pipe. You motor will sound much better than this one.

                  Comment


                    #84
                    Originally posted by muzzlebrake View Post
                    That setup screams Borla Atak with an X pipe. You motor will sound much better than this one.
                    https://youtu.be/VAfRG6bzC5c?t=114
                    I will definitely consider it and thanks for the suggestion sir. From your post, you definitely sound like you know what you’re talking about.

                    Comment


                      #85
                      Waiting on my buds to show up and it’s motor swap time!!! Going to do a quick verification on the motor and make sure she’s good then get the old motor out and the new one in. I pray I have all the parts and if I don’t, Oreillys does.

                      Comment


                        #86
                        Alright! The guys on Garage Squad tv show do it in 5 minutes. Shouldn't take yall but 10-15!

                        Comment


                          #87
                          Originally posted by Mr. Whiskers View Post
                          The bet I have is 500 HP for 500.00. I took the over.
                          What is the compression ratio?

                          Comment


                            #88
                            Originally posted by Mr. Whiskers View Post
                            Waiting on my buds to show up and it’s motor swap time!!! Going to do a quick verification on the motor and make sure she’s good then get the old motor out and the new one in. I pray I have all the parts and if I don’t, Oreillys does.
                            No silver bullets till its done!

                            Sent from my SM-G930V using Tapatalk

                            Comment


                              #89
                              Originally posted by Fordnandez View Post
                              What is the compression ratio?
                              With flat tops and the MS3 nitrous bump stick with wide LSA and depending on chamber volume I would guess around 9.5 to 9.8. Would also depend on timing gear setup. Earlier intake open raises cold cranking compression. Later intake open lowers CR. The devil is always in the details when engine building. Parts need to be matched to be compatible and compliment each other. Port matching intake to heads is often overlooked and when done properly is a good bonus.
                              Gotta wonder how it would feel with a 200 shot of NOX on -4 deg retard

                              Comment


                                #90
                                Originally posted by Quackerbox View Post
                                No silver bullets till its done!

                                Sent from my SM-G930V using Tapatalk
                                Said NO ONE EVER!

                                Comment

                                Working...
                                X