Reply
Go Back   TexasBowhunter.com Community Discussion Forums > Topics > D-I-Y Projects
 
Thread Tools Display Modes
Old 11-09-2006, 08:55 AM   #1
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default DH30's Homemade Ground Blind

Here are the instructions I put together a few years ago. I cannot find the pictures that went with this, but I'll keep looking. These instructions are based off a groundblind that Tuthdoc told me how to build. You can customize this blind to meet your needs, but here are the basic instructions:

1. Buy the materieals:
Cattle panel (qty=1)
½” CPVC (qty=3)
Camo spray paint (optional)
Green black rubber backed outdoor carpet (27’)
#12 solid core insulated electrical wire
Black cable ties (or zip ties as I call them)

2. Cut the cattle panel in half. Cut the horizontal wires against one of the vertical wires. (I only do this for transportation. If you can carry a 16’ panel, then there is no need to cut)

3. Paint the carpet camo.

4. Cut the bottom horizontal strand off the cattle panel creating “spikes” to stick into the ground.

5. Lay the carpet on the ground with the black backing facing up.

6. Connect the cattle panels together by bending the exposed horizontal wires around the vertical wire on the opposite panel.

7. Cut the carpet into two pieces. One at 20’ and one at 7’.

8. Lay the cattle panel down on top of the carpet leaving two feet of excess on each end to serve as a door. Stick the “spikes” at the bottom of the panel through the carpet about two inches from the bottom of the carpet. There will be extra carpet at the top. Leave that carpet to help cover the roof. Note: by adding the carpet to the panel while it is laying on the ground the carpet will be stretched good and tight when the panel is bent into a circle.

9. Use the tie straps to attaché the carpet to the cattle panels. I used one tie strap every third square around the perimeter of the cattle panel.

10. Bend the cattle panel into a circle.

11. Stand the cattle panel up.

12. Adjust the bend so the panel makes a circle with a 2’ gap at the back.

13. Use the bottom strand of wire to create a door header and footer. I use tie straps to attach this wire to the panel.

14. Push the bottom “spikes” into the ground.

15. Use tie straps to secure the “flaps” of carpet on the end of the panels to the door header. By having a “double flap” or carpet coming from both sides it creates a nice door that does not let light in.

16. Before attaching the roof, select the locations for the shooting windows and cut the cattle panel for those. I use a window that is one square wide and two squares tall which is about 8” wide and 12” tall. (By cutting the windows before the roof is on it allows you to sit in the blind and look over the top of the panel to select the best locations for the windows.

17. Cut the carpet out for the windows and tie strap around the perimeter of the window. I cut the top and both sides and then fold the flap of carpet down and tuck into the panel. This allows for the window to be re-closed at a later date if need be.

18. Cut some of the top vertical piece to create a few “spikes” to slide the CPVC over.

19. Cut the CPVC and place it over the vertical pieces to create a domed roof. I have found that 3 pieces of CPVC make a nice solid roof. I found that cutting the CPCV to about 8’-2” creates approximately a 6’ tall blind in the center.

20. Use tie straps to tie the CPVC together at the intersection at the top of the blind. This adds strength to the roof section.

21. Attach the carpet for the roof using tie straps. The carpet will sag some but I found that adding more tie straps to bunch up the extra carpet along with some of the solid core insulated wire stretched around the CPVC creates a solid roof.

22. Brush the blind in.
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 11-09-2006, 09:20 AM   #2
furhunter
Ten Point
 
furhunter's Avatar
 
Join Date: Oct 2006
Location: Frankston, TX
Hunt In: New York!!!lol
Default

hey thanks, I was just fixin to send you a PM to send me your directions!!lol You saved me some typing!!
furhunter is offline   Reply With Quote Back To The Top
Old 11-13-2006, 05:30 PM   #3
NateYJ
Ten Point
 
NateYJ's Avatar
 
Join Date: Oct 2006
Location: Cedar Park,Texas
Hunt In: Somewhere soon!!!
Default

Awesome DH30 got any pics!!!!
NateYJ is offline   Reply With Quote Back To The Top
Old 11-14-2006, 07:46 AM   #4
Dusty Britches
Pope & Young
 
Dusty Britches's Avatar
 
Join Date: Oct 2006
Location: Cameron & College Station
Default

I could follow the instructions very easily, except for steps 18-21. I'm a visual person, so I'm having trouble visualizing how you attach the CPVC to the spikes and how the solid core insulated wire streached around the CPVC makes a solid roof.

Wasn't there another thread recently that showed some of that?

Thanks for the instructions. I was thinking of building one of plywood and 2 x's, but this looks much easier.
Dusty Britches is offline   Reply With Quote Back To The Top
Old 01-04-2007, 12:38 PM   #5
texag93
Pope & Young
 
texag93's Avatar
 
Join Date: Oct 2006
Location: San Angelo, Tx
Hunt In: Panhandle
Default

What is the approx. cost of material for this project? I follow most of it but a pic is worth a thousand words for sure.
texag93 is offline   Reply With Quote Back To The Top
Old 01-04-2007, 02:17 PM   #6
Flint knapper
Ten Point
 
Flint knapper's Avatar
 
Join Date: Oct 2006
Location: Olney Tx
Hunt In: Young/Archer Co.
Default

Have you ever had any prolblems with wasps, stinging scorpions, or spiders getting into the stand while you were gone, Just to sting you when you return??
Flint knapper is offline   Reply With Quote Back To The Top
Old 01-04-2007, 02:50 PM   #7
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default

I'll try to dig up some pics tonight if I can find them. I'm not sure I can find them, but I'll see what I can do.

Dusty Britches,
Basically by bowing the CPVC and sticking it onto the spikes created by cutting the top of several vertical pieces it is connected. The tension created by the bowed CPVC keeps them on the panel. As far as using the solid core wire to strengthen the top......it's just a matter of connecting everything together.

Flint Knapper,
These blinds obviously make very good homes for spiders. I have spiders in mine almost every trip. When I hunted San Angelo during bow season the granddaddy-long-legs loved them. I would have hundreds or maybe even thousands of those spiders in the blind when I got there in the morning. As the sun rose they would all migrate out and then they would migrate back in during the evening.
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 01-04-2007, 06:38 PM   #8
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default

Here are the pictures that I have been able to find.

Attachment 7881

Attachment 7882

Attachment 7883

Attachment 7884
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 01-08-2007, 10:35 AM   #9
Dusty Britches
Pope & Young
 
Dusty Britches's Avatar
 
Join Date: Oct 2006
Location: Cameron & College Station
Default

Thanks, DH. Do you think it will survive a thrashing by mad heifers?
Dusty Britches is offline   Reply With Quote Back To The Top
Old 01-08-2007, 11:34 AM   #10
Snapper
Pope & Young
 
Snapper's Avatar
 
Join Date: Oct 2006
Location: Katy, Tx
Default

Very nice.
Snapper is offline   Reply With Quote Back To The Top
Old 01-08-2007, 05:21 PM   #11
RustyRanchero
Ten Point
 
RustyRanchero's Avatar
 
Join Date: Jan 2007
Location: Permian Basin
Default

Nice!
RustyRanchero is offline   Reply With Quote Back To The Top
Old 01-10-2007, 07:30 AM   #12
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default

Dusty Britches,
I would guess that some heifers could do some serious damage if they so chose. I can gurantee you that if you clip one with a brush hog, they do not fair very well! LOL
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 01-15-2007, 10:08 PM   #13
Mike D
Pope & Young
 
Mike D's Avatar
 
Join Date: Oct 2006
Location: North Texas
Hunt In: Haskell County, TX
Default

DH30,

I made one of these last year and the most challenging part was getting carpet on the roof. Something about making a square go onto something round. I just wasn't getting it. I managed but I'm sure there is a better way. Any tips?
Mike D is offline   Reply With Quote Back To The Top
Old 01-16-2007, 07:42 PM   #14
Walker
Ten Point
 
Walker's Avatar
 
Join Date: Oct 2006
Location: San Antonio
Default

We built some this year with concrete wire. Cut 21' section, make a circle and overlap the ends 3 squares. Made 3 roof bows out of 3/8" rebar, I think but not positive 10'long. Wrap with tap paper and do the roof with tar paper. Cut entry and shooting ports anywhere you want them.
Walker is offline   Reply With Quote Back To The Top
Old 01-16-2007, 08:54 PM   #15
Flint knapper
Ten Point
 
Flint knapper's Avatar
 
Join Date: Oct 2006
Location: Olney Tx
Hunt In: Young/Archer Co.
Default

Do you have any pic of the finished ground blind set up?
Flint knapper is offline   Reply With Quote Back To The Top
Old 01-19-2007, 03:10 PM   #16
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default

Mike,
I don't have any magic way to do the roof carpet. You are correct....getting a square flat piece of carpet to fit a dome is tricky. The best that I can describe what I do is to lay it over the top, ensure that the "pleats" created by placing a flat item over a domed shape are as even as possible and then use zip ties to bunch up the "pleats" as best as possible.

Flink knapper,
I don't really have any good pictures of the finished blind. The only decent pics I have are of my setups in San Angelo and they are brushed in so well that you cannot even see the blind.
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 05-07-2007, 01:45 AM   #17
AgHntr10
Pope & Young
 
AgHntr10's Avatar
 
Join Date: Oct 2006
Location: Lumberton
Hunt In: Where the thieves and poachers roam
Default

I think I am going to try my hand at making one of these, and if it turns out well possibly more. Thanks for the instructions
AgHntr10 is offline   Reply With Quote Back To The Top
Old 05-07-2007, 10:22 AM   #18
Adair
Banned!!!
 
Join Date: Apr 2007
Location: HARKER HEIGHTS, TX.
Default

How Much To Make The Whole Thing?
Adair is offline   Reply With Quote Back To The Top
Old 05-07-2007, 01:51 PM   #19
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default

I want to say that my last one cost about $80.
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 05-07-2007, 05:33 PM   #20
RustyRanchero
Ten Point
 
RustyRanchero's Avatar
 
Join Date: Jan 2007
Location: Permian Basin
Default

thanks for the pics, does it hold up well in the weather? Thats the only thing im worried about.
RustyRanchero is offline   Reply With Quote Back To The Top
Old 05-08-2007, 03:43 PM   #21
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default

They hold up VERY well in weather. I have had one out for several years and it's still in great shape.
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 05-08-2007, 06:10 PM   #22
shawn
Ten Point
 
shawn's Avatar
 
Join Date: Oct 2006
Location: League City
Hunt In: without a lease this go around.
Default

They will last for years and years in the elements. I had one out in Uvalde several years then moved it in one piece to S.Tx. and it worked great.
shawn is offline   Reply With Quote Back To The Top
Old 05-08-2007, 08:09 PM   #23
scotty
Pope & Young
 
scotty's Avatar
 
Join Date: Oct 2006
Location: Taylor,Tx
Hunt In: Encinal Texas, Hare, Texas
Default

We have five of these set out. Have been set up for around three years. Cost is about $80.00. Here are some inside and outside pics.
Attachment 21624

Attachment 21621

Attachment 21622

Attachment 21623
scotty is offline   Reply With Quote Back To The Top
Old 05-08-2007, 09:29 PM   #24
SAGEBRUSH ASSASSIN
Eight Point
 
SAGEBRUSH ASSASSIN's Avatar
 
Join Date: Apr 2007
Location: Odessa
Hunt In: Scurry and Crane County
Default

Very Creative.. I like the idea. might have to try it.
SAGEBRUSH ASSASSIN is offline   Reply With Quote Back To The Top
Old 05-08-2007, 11:14 PM   #25
hillcountryhunter
Ten Point
 
hillcountryhunter's Avatar
 
Join Date: Oct 2006
Location: Corpus Christi
Hunt In: Jim Wells County/Llano County
Default

Where is a good place to go to find the carpet and what are materials will work that are easily accessible other than carpet?
hillcountryhunter is offline   Reply With Quote Back To The Top
Old 05-09-2007, 11:15 AM   #26
AgHntr10
Pope & Young
 
AgHntr10's Avatar
 
Join Date: Oct 2006
Location: Lumberton
Hunt In: Where the thieves and poachers roam
Default

Has anyone tried putting shoot through netting on one yet?
AgHntr10 is offline   Reply With Quote Back To The Top
Old 05-09-2007, 03:25 PM   #27
bdchorn
Ten Point
 
bdchorn's Avatar
 
Join Date: Oct 2006
Location: Austin
Hunt In: Throckmorton
Default

These things are great and last a LONG time. I'm going on year 3 for one of mine and it looks like I put it up yesterday. I went a step further and lined the whole thing in a thick landscaping plastic. The good is that it virtually eliminates scent. The bad is the thing is a sweatlodge in October. For the money (less than $100), these things beat a pop up every day of the week if you don't need to move them around very often. We have others that are wrapped in burlap and that seems to work just as well as carpet, but the burlap will leak a bit in a bad rain.
bdchorn is offline   Reply With Quote Back To The Top
Old 05-09-2007, 03:57 PM   #28
Deerhunter30
Ten Point
 
Deerhunter30's Avatar
 
Join Date: Oct 2006
Location: Deer Park Texas / Gonzales County
Default

AgHntr10,
I had shoot thru windows on one of mine. I built a frame from 1X2s and stretched and stapled shoot thru mesh onto the frame. I then bent a couple of metal brackets so I could hang the frames on the cattle panel.
Deerhunter30 is offline   Reply With Quote Back To The Top
Old 05-09-2007, 04:59 PM   #29
scotty
Pope & Young
 
scotty's Avatar
 
Join Date: Oct 2006
Location: Taylor,Tx
Hunt In: Encinal Texas, Hare, Texas
Default

I get my carpet at Home Depot. It comes in rolls that are 5x8. It takes three rolls. It comes in two "weights". The more expensive one, (by a couple of dollars), is thicker and blocks out the light better. Two for the walls and one for the roof. I use a piece of heavy carpet for the door. We also drive two t-posts in to anchor the sides of the door. I found that if you roll the cattle panel into a circle after you put the carpet on, it sets up a lot easier. In my pictures above, the blind has netting over the window. I just zip-tie the netting to the cattle panel.
scotty is offline   Reply With Quote Back To The Top
Old 05-09-2007, 10:24 PM   #30
AgHntr10
Pope & Young
 
AgHntr10's Avatar
 
Join Date: Oct 2006
Location: Lumberton
Hunt In: Where the thieves and poachers roam
Default

Oh sorry, I didn't even notice the netting in the pictures above. If nothing happens I am going to try to set one up this weekend and I will have some pictures up next week.
AgHntr10 is offline   Reply With Quote Back To The Top
Old 05-21-2007, 10:51 AM   #31
Matt2006Martin
Ten Point
 
Matt2006Martin's Avatar
 
Join Date: Oct 2006
Location: San Antonio/Jim Thorpe PA
Hunt In: My Ranch
Default

nice job
Matt2006Martin is offline   Reply With Quote Back To The Top
Old 05-22-2007, 10:39 AM   #32
Dr. D
Pope & Young
 
Dr. D's Avatar
 
Join Date: May 2007
Location: Clifton, Texas/Bosque Co.
Hunt In: Bosque Co. and anyplace else I can.
Default

cool idea guys...Ima gonna steal it..lol.thanks
Dr. D is offline   Reply With Quote Back To The Top
Old 10-08-2007, 07:46 PM   #33
cajundave
Guest
 
Talking

I started mine today but forgot my pvc at home. I will have to got back. Question, I'm thinking of using rebarb to hold it down. The sides came out great and I'm excited about it.
  Reply With Quote Back To The Top
Old 10-27-2007, 09:29 AM   #34
scotty
Pope & Young
 
scotty's Avatar
 
Join Date: Oct 2006
Location: Taylor,Tx
Hunt In: Encinal Texas, Hare, Texas
Default

Must have lost my pictures in the last crash. Here they are again.

Name:  129_2981_r1 (Medium).jpg
Views: 23923
Size:  48.6 KB

Name:  129_2982_r1 (Medium).jpg
Views: 23853
Size:  56.7 KB

Name:  129_2983 (Medium).JPG
Views: 23878
Size:  48.4 KB

Name:  129_2979 (Medium) (Small).JPG
Views: 24338
Size:  99.2 KB
scotty is offline   Reply With Quote Back To The Top
Old 02-12-2008, 07:47 AM   #35
bwssr
Pope & Young
 
bwssr's Avatar
 
Join Date: Oct 2006
Location: Madisonville, Texas
Hunt In: Madison county
Default

Bump For Soxt
bwssr is offline   Reply With Quote Back To The Top
Old 02-12-2008, 07:57 AM   #36
sotx
Ten Point
 
sotx's Avatar
 
Join Date: Oct 2006
Location: San Antonio, TX
Hunt In: McMullen County
Default

thanks!!!!!!!!!!!!!!!!!!!!!!!!!
sotx is offline   Reply With Quote Back To The Top
Old 05-29-2008, 12:29 PM   #37
Chew
Pope & Young
 
Chew's Avatar
 
Join Date: Oct 2006
Location: Kingwood, TX
Hunt In: Leon County
Default

Anyone else got pictures of the building process? Thanks.
Chew is offline   Reply With Quote Back To The Top
Old 05-29-2008, 10:22 PM   #38
Burnadell
Pope & Young
 
Burnadell's Avatar
 
Join Date: Oct 2006
Default

Quote:
Originally Posted by Chew View Post
Anyone else got pictures of the building process? Thanks.

See if these help, Bobby.

Name:  groundblind1.jpg
Views: 25717
Size:  33.8 KB

Name:  groundblind2.jpg
Views: 29083
Size:  29.0 KB

Name:  groundblind3.jpg
Views: 22815
Size:  80.5 KB

Name:  groundblind4.jpg
Views: 22674
Size:  14.8 KB

Name:  groundblind5.jpg
Views: 22784
Size:  128.3 KB

Name:  groundblind6.jpg
Views: 35372
Size:  107.5 KB

Name:  groundblind7.jpg
Views: 22829
Size:  133.6 KB

Name:  groundblind8.jpg
Views: 24587
Size:  134.2 KB

Name:  groundblind9.jpg
Views: 22346
Size:  99.0 KB

Name:  groundblind10.jpg
Views: 38796
Size:  115.5 KB
Burnadell is offline   Reply With Quote Back To The Top
Old 05-30-2008, 06:37 AM   #39
Chew
Pope & Young
 
Chew's Avatar
 
Join Date: Oct 2006
Location: Kingwood, TX
Hunt In: Leon County
Default

Thanks! Those are great.

Can someone tell me about the roof in pic 2. What's up with the plastic? How does that work?

So the door is completely cut out after the blind is made into a circle (except for the top strand of wire?) The door isn't cut out when the cattle panel is lying on the carpet, just wondering the order you do it in.

Thanks.
Chew is offline   Reply With Quote Back To The Top
Old 05-30-2008, 11:43 AM   #40
jay
Ten Point
 
jay's Avatar
 
Join Date: Oct 2006
Location: Spring
Hunt In: Sutton and Leon County
Default

Chew, the plastic adds to the water resistance. I have used it on both of the blinds I have made like this and neither have leaked.

When I made one of mine, I used (2) 2X4's for my door. I bent the panel around and used fence staples to nail the panel to the wood for my opening. One on top and one on the bottom. Gave me a little bigger blind this way. The second one I made, I drove t-posts in the ground where I wanted my door and wired the panel to them and used the opening between the t-posts for my door. Both of my blinds required a little more carpet for the added room.

I am planning on building another out at the lease next weekend. I am going to frame a back wall (back wall will be skinned with plywood) with a hinged door for this one and use the pannel for the rest. I want to be able to lock my blind up and feel this is the best way to accomplish this.
jay is offline   Reply With Quote Back To The Top
Old 05-30-2008, 11:49 AM   #41
Chew
Pope & Young
 
Chew's Avatar
 
Join Date: Oct 2006
Location: Kingwood, TX
Hunt In: Leon County
Default

Thanks jay. Is that some heavy duty special plastic?

What diameter would you say the blinds end up being? Plenty room to draw back in? Room for 2 people? Thanks.
Chew is offline   Reply With Quote Back To The Top
Old 05-30-2008, 11:58 AM   #42
jay
Ten Point
 
jay's Avatar
 
Join Date: Oct 2006
Location: Spring
Hunt In: Sutton and Leon County
Default

The plastic I used was just some 4 mil painters plastic.

http://www.lowes.com/lowes/lkn?actio...25C&lpage=none

My blinds are a little bigger than my double bull blinds. You can easily hunt two from them.
jay is offline   Reply With Quote Back To The Top
Old 03-02-2009, 10:20 AM   #43
ArrowHead
Ten Point
 
ArrowHead's Avatar
 
Join Date: Oct 2006
Location: Fort Worth,Tx.
Hunt In: Mills county
Default

Can someone give me the length of the roof poles (PVC)?How long to cut them? 8' something?Can not read the info. in the orginal thread.Thanks in advance.
ArrowHead is offline   Reply With Quote Back To The Top
Old 03-02-2009, 01:24 PM   #44
BowCrazy
Ten Point
 
BowCrazy's Avatar
 
Join Date: Oct 2006
Location: Gilmer TX.
Hunt In: ???? Tx.
Default

Can we get more pics of the roof? How the poly was added.
BowCrazy is offline   Reply With Quote Back To The Top
Old 03-02-2009, 01:43 PM   #45
Reaper
Pope & Young
 
Reaper's Avatar
 
Join Date: Oct 2007
Location: Austin
Hunt In: the woods
Default

can't wait to do this
Reaper is offline   Reply With Quote Back To The Top
Old 03-02-2009, 03:54 PM   #46
Ron
Pope & Young
 
Ron's Avatar
 
Join Date: Jan 2009
Location: Kings Creek Golf Club, Kemp TX
Hunt In: USA, Concho County and S.E.Colorado
Default

Nice blinds, all of them.
Ron is offline   Reply With Quote Back To The Top
Old 03-03-2009, 08:40 PM   #47
DiscusD
Spike
 
Join Date: Aug 2008
Default

Looks like a pretty low cost blind i like the idia
DiscusD is offline   Reply With Quote Back To The Top
Old 05-15-2009, 09:37 PM   #48
bsills
Pope & Young
 
bsills's Avatar
 
Join Date: Aug 2008
Location: Fair Oaks
Hunt In: Maverick County
Default

I have looked through about every thread I can find and this is the best idea for a ground blind that I can find. Does any one that has done this have any advice for a first timer? Any modifications ya'll have implemented to the design that you like please let me know. I would also love to see any more pics that might be out there.
Thanks
bsills is offline   Reply With Quote Back To The Top
Old 05-15-2009, 10:37 PM   #49
Drenalin_Ag99
Ten Point
 
Drenalin_Ag99's Avatar
 
Join Date: Oct 2007
Location: Flint, TX
Hunt In: Henderson County
Default

Man how does that hold up to windy west texas? My rifle blind on the ground was blown smooth over the other day. I like just curious if the wind was huge factor? How do you haul to lease, easy to break down?

Last edited by Drenalin_Ag99; 05-15-2009 at 10:43 PM..
Drenalin_Ag99 is offline   Reply With Quote Back To The Top
Old 05-16-2009, 08:42 AM   #50
bsills
Pope & Young
 
bsills's Avatar
 
Join Date: Aug 2008
Location: Fair Oaks
Hunt In: Maverick County
Default

Quote:
Originally Posted by Drenalin_Ag99 View Post
Man how does that hold up to windy west texas? My rifle blind on the ground was blown smooth over the other day. I like just curious if the wind was huge factor? How do you haul to lease, easy to break down?
I am thinking these are permenant once set up. I am not thinking they are hauling them in and out of the woods.
bsills is offline   Reply With Quote Back To The Top
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:36 AM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 1999-2012, TexasBowhunter.com