how to time hoyt cam and a half - TexasBowhunter.com Community Discussion Forums

casilva43 · 10-12-2012, 08:30 AM

I have a hoyt with spiral cams. when drawing the bow, my bottom cam draw stop is hitting slightly quicker than my top cam. My top cam is under rotated.

Do I need to put twists into my bus cable or control cable to fix the problem. How many twists do I need to put in?

splitbeam145 · 10-12-2012, 08:43 AM

You can do either way. Depending on how much it's out of time. If's it just a little put one full twist in buss cable then check timing. If it need alittle more then just add another twist to buss cable and check again. If it's needs more than that take a twist OUT of the Control cable. To fine tune it at this point you could do just half a twist to perfect it.

casilva43 · 10-12-2012, 09:29 AM

Quote:

Originally Posted by splitbeam145

You can do either way. Depending on how much it's out of time. If's it just a little put one full twist in buss cable then check timing. If it need alittle more then just add another twist to buss cable and check again. If it's needs more than that take a twist OUT of the Control cable. To fine tune it at this point you could do just half a twist to perfect it.

Thank you very much for your help. How much will one twist affect draw length? Will I be able to tell?

Dchilds · 10-12-2012, 10:12 AM

One twist will not be felt in your draw length. I doubt it would even be measurable. I know it's not in my binary cammed Elite or any other binary cam bow I've owned. Good luck and let us know how it goes. By the way, a correctly timed bow will be quieter and provide better nock travel. So, it's worth the effort! You probably know that already.

ken1965 · 10-12-2012, 10:25 AM

I shoot a Hoyt Vantage Elite & Pro Elite for 3D, both with spiral cams. Go to Hoyt's website and co to Customer Service, go to the the bow tune charts and select your bow to get the ATA and brace height, along with the string and cable lengths. I put twist in the cables to make the 1/8 shorter than spec and do the same to the string and make that 3/16 shorter than spec. Then recheck your ATA and brace, its should be really close and the timing should almost be perfect.

To answer your initial question, if your top cam is out a lil at full draw, you need to add twist to your buss cable. If ya need any assistance just bring it to me at All Star in Lewisville and I will help ya.

splitbeam145 · 10-12-2012, 10:34 AM

If you start putting 3-4 twist in your cables then DL will start to change some. I measure DL with a arrow then start making adjustment then double check DL as I go along.

txdukklr · 10-12-2012, 12:00 PM

i thought the point of the cam.5 is that you don't have cam timing issues. . . . I had four of them when they first came out and never had to time the cams to each other.

Phi Phi Hunter · 10-12-2012, 12:10 PM

I need a diagram of the cable...which one is which? Buss/Contol?

Double L · 10-12-2012, 12:25 PM

Quote:

Originally Posted by Phi Phi Hunter

I need a diagram of the cable...which one is which? Buss/Contol?

Buss cable would be the one with the Y cable that attaches to the top limb. Control cable goes from cam to cam. Check Hoyt website for a manual on your bow.

bowtech1543 · 10-16-2012, 03:19 AM

Carlos you could had just asked me, don't you know I know everything.

-blake

60 Deluxe · 10-16-2012, 06:16 AM

There is a sticky in Archery Talk.com under the bow tuning forum. It is worth the read.

10-12-2012, 08:30 AM	#1
casilva43 Ten Point Join Date: Mar 2010 Location: Argyle Hunt In: Anywhere	how to time hoyt cam and a half I have a hoyt with spiral cams. when drawing the bow, my bottom cam draw stop is hitting slightly quicker than my top cam. My top cam is under rotated. Do I need to put twists into my bus cable or control cable to fix the problem. How many twists do I need to put in?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-12-2012, 08:43 AM	#2
splitbeam145 Ten Point Join Date: Jul 2008 Location: weatherford,tx	You can do either way. Depending on how much it's out of time. If's it just a little put one full twist in buss cable then check timing. If it need alittle more then just add another twist to buss cable and check again. If it's needs more than that take a twist OUT of the Control cable. To fine tune it at this point you could do just half a twist to perfect it.

10-12-2012, 10:12 AM	#4
Dchilds Eight Point Join Date: Aug 2010 Location: Richardson Hunt In: Red River Co.	One twist will not be felt in your draw length. I doubt it would even be measurable. I know it's not in my binary cammed Elite or any other binary cam bow I've owned. Good luck and let us know how it goes. By the way, a correctly timed bow will be quieter and provide better nock travel. So, it's worth the effort! You probably know that already.

10-12-2012, 10:25 AM	#5
ken1965 Spike Join Date: Mar 2012 Location: Grapevine, TX	I shoot a Hoyt Vantage Elite & Pro Elite for 3D, both with spiral cams. Go to Hoyt's website and co to Customer Service, go to the the bow tune charts and select your bow to get the ATA and brace height, along with the string and cable lengths. I put twist in the cables to make the 1/8 shorter than spec and do the same to the string and make that 3/16 shorter than spec. Then recheck your ATA and brace, its should be really close and the timing should almost be perfect. To answer your initial question, if your top cam is out a lil at full draw, you need to add twist to your buss cable. If ya need any assistance just bring it to me at All Star in Lewisville and I will help ya.

10-12-2012, 10:34 AM	#6
splitbeam145 Ten Point Join Date: Jul 2008 Location: weatherford,tx	If you start putting 3-4 twist in your cables then DL will start to change some. I measure DL with a arrow then start making adjustment then double check DL as I go along.

10-12-2012, 12:00 PM	#7
txdukklr Pope & Young Join Date: Oct 2006 Location: Sugarland Hunt In: Victoria	i thought the point of the cam.5 is that you don't have cam timing issues. . . . I had four of them when they first came out and never had to time the cams to each other.

10-12-2012, 12:10 PM	#8
Phi Phi Hunter Ten Point Join Date: Dec 2008 Location: Canyon Lake area(above Rocky Top Ranch) Hunt In: Back yard	I need a diagram of the cable...which one is which? Buss/Contol?

10-16-2012, 03:19 AM	#10
bowtech1543 Nubbin' Buck Join Date: Oct 2012	Carlos you could had just asked me, don't you know I know everything. -blake

10-16-2012, 06:16 AM	#11
60 Deluxe Ten Point Join Date: Sep 2012 Location: Coke County Hunt In: at home	There is a sticky in Archery Talk.com under the bow tuning forum. It is worth the read.