TC Encore Trigger Adjustment - TexasBowhunter.com Community Discussion Forums

dtu11 · 10-24-2009, 10:19 AM

Anyone here ever adjusted a trigger on a TC Encore? If it's not too hard, I may do it myself. But might consider taking it to a gunsmith to adjust it. If so, where would you suggest in the San Antonio area?

Mike D · 10-24-2009, 10:31 AM

There is no adjustment per se, you have to perform a full bore trigger job on it.

Mike Bellm does the best in the business. Unfortunately he is not taking any orders at the moment.

He has parts and instructions on how to do it on his site www.bellmtcs.com and he has partnered with a gunsmith in his area to do them for him. I have not had one done by that guy but if Bellm trusts him, he probably does good work.

tx_dropem · 10-24-2009, 12:13 PM

Quote:

Originally Posted by Mike D

There is no adjustment per se, you have to perform a full bore trigger job on it.

Mike Bellm does the best in the business. Unfortunately he is not taking any orders at the moment.

He has parts and instructions on how to do it on his site www.bellmtcs.com and he has partnered with a gunsmith in his area to do them for him. I have not had one done by that guy but if Bellm trusts him, he probably does good work.

x2, but it cost a pretty penny!

Mike D · 10-24-2009, 04:41 PM

Quote:

Originally Posted by tx_dropem

x2, but it cost a pretty penny!

And it is worth every penny. It is the finest trigger of any gun I own. He used to run a special for $88 and that is when I had mine done. If you are adventurous his kits are very reasonably priced.

skeeter · 10-24-2009, 04:43 PM

I need to get a trigger job done on my Encore.

kenforu · 10-24-2009, 08:11 PM

I had mine done at MG Arms here in Houston and it cost 75.00 set at 2.5lbs he did a great job and it makes a great deal of difference from factory.

Passthrough · 10-24-2009, 10:17 PM

Anyone know where you can get one done in North Texas..I have an Encore that is TOO HEAVY!! Metroplex area would be fine?

1 big skeeter · 10-25-2009, 05:05 AM

Quote:

Originally Posted by Mike D

There is no adjustment per se, you have to perform a full bore trigger job on it.

Mike Bellm does the best in the business. Unfortunately he is not taking any orders at the moment.

He has parts and instructions on how to do it on his site www.bellmtcs.com and he has partnered with a gunsmith in his area to do them for him. I have not had one done by that guy but if Bellm trusts him, he probably does good work.

I had my TC done 2 yrs ago by the gunsmith Mike uses since he was booked solid.

Sent JUST the action in and received it completed within a week.

Went from 7 pounds stock to 2 1/2 CRISP pounds.

For me, it's just right!!

firecapt186 · 10-25-2009, 09:07 AM

I have a friend that knows how to do the encore's, the pro hunter's don't do as good tho. He got mine down to 2.6#, no creep or after travel.

kenforu · 10-25-2009, 09:17 AM

You can also send just the frame into TC Pro shop and they can do it for you said it would take about a week to have it completed. Just go to their web site and they have a link that will give you all the info.

Luck_of_the_Draw · 10-25-2009, 11:03 AM

I did mine. With a little work and a new spring. Nothing to it.

10-24-2009, 10:19 AM	#1
dtu11 Eight Point Join Date: Oct 2007 Location: Cibolo Hunt In: No where atm	TC Encore Trigger Adjustment Anyone here ever adjusted a trigger on a TC Encore? If it's not too hard, I may do it myself. But might consider taking it to a gunsmith to adjust it. If so, where would you suggest in the San Antonio area?

10-25-2009, 09:07 AM	#9
firecapt186 Six Point Join Date: Jun 2007 Location: South Louisiana Hunt In: All over the U. S.	I have a friend that knows how to do the encore's, the pro hunter's don't do as good tho. He got mine down to 2.6#, no creep or after travel. Last edited by firecapt186; 10-25-2009 at 09:22 AM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-24-2009, 10:31 AM	#2
Mike D Pope & Young Join Date: Oct 2006 Location: DFW Hunt In: Haskell County, TX	There is no adjustment per se, you have to perform a full bore trigger job on it. Mike Bellm does the best in the business. Unfortunately he is not taking any orders at the moment. He has parts and instructions on how to do it on his site www.bellmtcs.com and he has partnered with a gunsmith in his area to do them for him. I have not had one done by that guy but if Bellm trusts him, he probably does good work.

10-24-2009, 04:43 PM	#5
skeeter Pope & Young Join Date: Oct 2006 Location: Cypress, TX Hunt In: Lavaca, Kimble and Colorado Counties	I need to get a trigger job done on my Encore.

10-24-2009, 08:11 PM	#6
kenforu Ten Point Join Date: Jan 2007 Location: conroe texas Hunt In: Junction, and Colorado	I had mine done at MG Arms here in Houston and it cost 75.00 set at 2.5lbs he did a great job and it makes a great deal of difference from factory.

10-24-2009, 10:17 PM	#7
Passthrough Ten Point Join Date: Oct 2006 Location: North Texas	Anyone know where you can get one done in North Texas..I have an Encore that is TOO HEAVY!! Metroplex area would be fine?

10-25-2009, 09:17 AM	#10
kenforu Ten Point Join Date: Jan 2007 Location: conroe texas Hunt In: Junction, and Colorado	You can also send just the frame into TC Pro shop and they can do it for you said it would take about a week to have it completed. Just go to their web site and they have a link that will give you all the info.

10-25-2009, 11:03 AM	#11
Luck_of_the_Draw Ten Point Join Date: Oct 2006 Location: North DFW Hunt In: Montague Co.	I did mine. With a little work and a new spring. Nothing to it.