Originally posted by softpoint
View Post
Announcement
Collapse
No announcement yet.
what is best chainsaw length for cutting hill country cedars
Collapse
X
-
Originally posted by Kossetx View Post
Comment
-
I have been using this cheap Stihl MS170 with 16" bar for a few years. It has not missed a beat. I used it to cut down pines at our house in PA and I also used it to make hinge cuts and clear a road at my friends farm in Ohio. I had a Craftsman 18" from 2002-2014 but that thing was a bear to start since new. I gave it away in a fit of frustration one day and bought this Stihl . I am happy I did.
Comment
-
Use a file to sharpen your chains and put the money you save toward the saw you want. You can buy a new full-chisel chain for what it'll cost you to have a chain sharpened twice. You'll save a LOT of time by not constantly swapping chains. I can run 25 tanks through my bigger saw before I ever take a chain off and more on my smaller ones. You'll get it (and keep it) much sharper than the kid at the hardware store and save lots of wear on yourself, too.
I don't see any reason a 16" bar wouldn't work for cedar, but I haven't cut a lot of it. .
Sent from my iPhone using Tapatalk
Comment
-
Originally posted by stickbowcoop View PostI have been using this cheap Stihl MS170 with 16" bar for a few years. It has not missed a beat. I used it to cut down pines at our house in PA and I also used it to make hinge cuts and clear a road at my friends farm in Ohio. I had a Craftsman 18" from 2002-2014 but that thing was a bear to start since new. I gave it away in a fit of frustration one day and bought this Stihl . I am happy I did.
Comment
-
Originally posted by JonW View PostUse a file to sharpen your chains and put the money you save toward the saw you want. You can buy a new full-chisel chain for what it'll cost you to have a chain sharpened twice. You'll save a LOT of time by not constantly swapping chains. I can run 25 tanks through my bigger saw before I ever take a chain off and more on my smaller ones. You'll get it (and keep it) much sharper than the kid at the hardware store and save lots of wear on yourself, too.
I don't see any reason a 16" bar wouldn't work for cedar, but I haven't cut a lot of it. .
Sent from my iPhone using Tapatalk
The Napa in town charges me $6 to sharpen. So I just have a few blades and rotate them there.
I have cut down literally hundreds of cedars off my place since I bought it 2.5 years ago. Stihl 171 16" gets it done. My buddy brings out his Stihl with the 20" bar and after about 45 min I am ready to toss that thing down the hill
Comment
-
Originally posted by rsquared View PostI looked at a few yesterday at a local dealer
Was really impressed with the echo 2511t as it is only 5 lbs
Also liked the echo 355t
I think a smaller top handle is the way I am going to go
Just need to decide which one
Comment
-
Originally posted by asttbe View PostThe Napa in town charges me $6 to sharpen. So I just have a few blades and rotate them there.
I have cut down literally hundreds of cedars off my place since I bought it 2.5 years ago. Stihl 171 16" gets it done. My buddy brings out his Stihl with the 20" bar and after about 45 min I am ready to toss that thing down the hill
I think they're $7 around here. I haven't bought a 16" chain lately but the 20" have gone up to around $17 at the saw shop (not lawn equipment) I buy from. Lawnmower shops are expensive for some reason and many won't sell anything but safety chains.
I sharpen a chain (touch-up really) an average of 25 times with a file. Normally it's tooth wear at that point, but if I don't do as good a job as I should I've had them stretch before. It doesn't make sense cost-wise for me (I can buy a lot of new chains if I paid to have them sharpened) but that's just my experience. Either way, I have to touch up teeth after the machines because they don't get them as sharp as a file does. And I'm really not that proficient. I might even do better with a guide.
Sent from my iPhone using Tapatalk
Comment
-
I have 3 Echo's and 5 Stihl saws.
The Echo are lighter and less vibration if you are running even for a half hour there is a big difference. My primary saw is a 27" Echo 680 but I bring smaller 18's and 20's. The big saw makes quick work of a log, it will save a lot of time when cutting big wood. Some say it is overkill but it is too small for many jobs. I like the sound of the Stihl though reminds me of my motocross days. Brrrrp brrrrrrp
If I was going to just cut on occasion I would buy an Echo and not have to think about it again.
Comment
-
Overall I prefer the new Echo's over the new Stihl saws. The Stihl MS250 is a proven saw though. Some of the big logging Stihl saws that are still made in Germany are the cats Meow. The older Stihls reputation was solid, and it's still carrying their new line of junk. I had two Stihls (MS291) and (MS 170). Both were junk to me. I sold both of them and run an Echo CS 590. I have a 24" and 18" bar for it. I can pretty much do everything I need too with that saw. I have thought about getting a Milwaukee M18 chain saw for smaller task. I have no experience with HusqvarnaLast edited by Arrowthreat; 01-05-2021, 08:55 AM.
Comment
Comment