A C repair gents - TexasBowhunter.com Community Discussion Forums

Death from Above · 05-06-2012, 10:16 PM

I need help.

Outside fan motor is going out. Anyone know of a parts warehouse in east Texas I can get one ?

3 ton unit.

Thanks

Strummer · 05-06-2012, 10:18 PM

Do you have a service supply near by ?

Kingslayer · 05-06-2012, 10:22 PM

That is not a cheap part

Twztid · 05-06-2012, 10:23 PM

You know supply houses have to sell to home owners doing work on there own home....look on the side of the motor get horse power h/p ? And RPM speed 875/1075 and walk into a supply house and say "need a condenser fan motor this Hp and this rpm say its for my house and they by law have to sell it...you just can't walk in there and buy a motor for some ones else's house with intent to charge money...a motor should put you from 60$/100$ if worst comes to worst let me know what town your in and I can put one in will call at a supply house...I have accounts set up with most all major ones, insco,carrier,trane,ince,York...But try on your own first it works or order one online like everyone else does

Xenarcher · 05-06-2012, 11:01 PM

You can try Coburns in Lufkin.... 936-634-5539
Ask for Cory

MA ELite · 05-06-2012, 11:13 PM

Johnstone Supply in Tyler.

chancito1 · 05-06-2012, 11:16 PM

Be careful they do have to sell to you but they will jack you up on price. I've seen homeowners pay 4 times the amount the part costs me.

JEG8233 · 05-06-2012, 11:44 PM

Try this company. They are based in Tyler. Here is there web page so you can look up your motor once you get the info on it. It maybe be cheaper then going thru an a/c parts house as a home owner.

https://www.applied.com/apps/commerc...og.do?e=2&c=42

Death from Above · 05-07-2012, 07:22 AM

Thanks guys. I found one. Will put it in today. ALOT cheaper than calling in an AC repair man. Good thing is I spend about 20 k a year on heating and cooling thru my church. The warehouses are willing to help me out.

red · 05-07-2012, 07:27 AM

dont know if there is a grainger near you, they had a replacement for mine when it went out. just under $100, and replaced myself

Ironman · 05-07-2012, 07:54 AM

Grainier has about any electric motor you could want. Match HP, RPM, and length, bolt pattern, shaft length.
Mine went out, and this is what I did. If I remember correctly, I had to cut the length of the shaft down. Just make sure you get shaft diameter right, and you will be fine.

Dawg · 05-07-2012, 08:02 AM

Quote:

Originally Posted by Death from Above

Thanks guys. I found one. Will put it in today. ALOT cheaper than calling in an AC repair man. Good thing is I spend about 20 k a year on heating and cooling thru my church. The warehouses are willing to help me out.

Good deal. I was going to suggest Coburns as well.

This time of the year is not a good time to have AC problems.

05-06-2012, 10:16 PM	#1
Death from Above Pope & Young Join Date: Oct 2006 Location: Henderson Hunt In: Texas	A C repair gents I need help. Outside fan motor is going out. Anyone know of a parts warehouse in east Texas I can get one ? 3 ton unit. Thanks

05-06-2012, 10:23 PM	#4
Twztid Ten Point Join Date: Aug 2011 Location: La Vernia Hunt In: Wilson Co.	You know supply houses have to sell to home owners doing work on there own home....look on the side of the motor get horse power h/p ? And RPM speed 875/1075 and walk into a supply house and say "need a condenser fan motor this Hp and this rpm say its for my house and they by law have to sell it...you just can't walk in there and buy a motor for some ones else's house with intent to charge money...a motor should put you from 60$/100$ if worst comes to worst let me know what town your in and I can put one in will call at a supply house...I have accounts set up with most all major ones, insco,carrier,trane,ince,York...But try on your own first it works or order one online like everyone else does Last edited by Twztid; 05-06-2012 at 10:28 PM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-06-2012, 10:18 PM	#2
Strummer Ten Point Join Date: Oct 2006 Location: Edna Tx Hunt In: At Gary's place ,and the backyard	Do you have a service supply near by ?

05-06-2012, 10:22 PM	#3
Kingslayer Ten Point Join Date: Mar 2010 Location: Braavos	That is not a cheap part

05-06-2012, 11:01 PM	#5
Xenarcher Six Point Join Date: Jan 2012 Location: Alvin Hunt In: Jewett	You can try Coburns in Lufkin.... 936-634-5539 Ask for Cory

05-06-2012, 11:13 PM	#6
MA ELite Ten Point Join Date: May 2007 Location: Sterling, OK Hunt In: Oklahoma/Texas	Johnstone Supply in Tyler.

05-06-2012, 11:16 PM	#7
chancito1 Ten Point Join Date: Oct 2011 Location: Bastrop Tx Hunt In: Junction/South Texas	Be careful they do have to sell to you but they will jack you up on price. I've seen homeowners pay 4 times the amount the part costs me.

05-06-2012, 11:44 PM	#8
JEG8233 Ten Point Join Date: Jun 2009 Location: San Antonio Hunt In: Caldwell County and New Mexico	Try this company. They are based in Tyler. Here is there web page so you can look up your motor once you get the info on it. It maybe be cheaper then going thru an a/c parts house as a home owner. https://www.applied.com/apps/commerc...og.do?e=2&c=42

05-07-2012, 07:22 AM	#9
Death from Above Pope & Young Join Date: Oct 2006 Location: Henderson Hunt In: Texas	Thanks guys. I found one. Will put it in today. ALOT cheaper than calling in an AC repair man. Good thing is I spend about 20 k a year on heating and cooling thru my church. The warehouses are willing to help me out.

05-07-2012, 07:27 AM	#10
red Ten Point Join Date: Oct 2006 Location: Midlothian, TX Hunt In: Young & Taylor co.	dont know if there is a grainger near you, they had a replacement for mine when it went out. just under $100, and replaced myself

05-07-2012, 07:54 AM	#11
Ironman Ten Point Join Date: Jan 2010 Location: Flower Mound Hunt In: Anywhere	Grainier has about any electric motor you could want. Match HP, RPM, and length, bolt pattern, shaft length. Mine went out, and this is what I did. If I remember correctly, I had to cut the length of the shaft down. Just make sure you get shaft diameter right, and you will be fine.