Pulled a wire to check the plugs....broke 4 wires.....
Fun, fun, fun!!!
Sent from my iPhone using Tapatalk
Fun, fun, fun!!!
Sent from my iPhone using Tapatalk
-
Ultramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_) -
Don't think these 2 fellas are sposed to touch each other....
Gonna try a 2" shorter belt....maybe 1"....
Sent from my iPhone using TapatalkUltramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
-
How long you gonna leave them old cast manifolds on there?Comment
-
Until I stick another bullet in it.
Loud enuff as it is!
Sent from my iPhone using TapatalkUltramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
-
You been doing wok hand!
Nice improvements!
Comment
-
Thanks!
Sent from my iPhone using TapatalkUltramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
-
Originally posted by Joey~AP View PostBeefy!!!
Sent from my iPhone using Tapatalk
Looks good!
You don't need the misalignment spacers on the tie rod, only on the draglink. Drill and cotter pin the bolts or safety wire for added peace of mind.
Sent from my iPhone using Tapatalk ProComment
-
I was lookin at that. I will fix it before I tighten everything down.
Sent from my iPhone using TapatalkUltramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
-
70 Bronco ~ FrankenFord
You'll love the DOM steering linkage
I put a misalignment spacer on both sides of the rod end at both ends of the drag link (need to find the missing rascal for the pitman side)
Take a look at the panhard bar (track bar) in relation to your drag link.
Ideally, they should be the same angle, and the same length so as the axle droops when the suspension is cycling, they are not exerting opposing forces on the steering. This is often referred to as "bump steer"
I used a track bar riser from Wild Horses to bring the axle end if my track bar up. It welds to the axle.
You can just see it tucked in the back. I need to drill and pin my bolts. Daughter just helped me get it all back assembled a few days ago.
My next obstacle is getting the pulley pressed back on my power steering pump. I don't have a beefy enough impact. My rig came with factory power steering, but it has been completely rebuilt by PSC Motorsports. I'm debating on whether I want to install the ram assist, or leave it off. I had the box ported to accept it, and the ram is on my tool cart.
Your thread has given me some inspiration (and some ideas) as I reassemble my rig. I appreciate it.Last edited by Gummi Bear; 04-25-2017, 02:59 PM.Comment
-
Yessir! Start a thread on it. I'd like to see it.
Sent from my iPhone using TapatalkUltramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
-
Christmas time in Texas!!!
Sent from my iPhone using TapatalkUltramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
-
Found a center console that should fit today.....
Old mermite!
Sent from my iPhone using TapatalkUltramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
-
Where did you find that?
That is cool, extremely cool.
I have a Tuffy, one of the first they made. http://www.tuffyproducts.com/p-85-de...le-8-wide.aspx
Sent from my iPhone using Tapatalk ProComment
-
That is a sweet Bronco!!!!Comment
-
Ultramatic Feeders
We're paratroopers, Lieutenant. We're supposed to be surrounded......
/l _ ,[____],
l---- L-- -OlllllllO-
()_)--()_)---o-)_)Comment
Comment